Nutanix Cloud Infrastructure

Hello, I have installed a 2 Node cluster using nutanix foundation VM with witness node as a tie breaker in dell xc4510 and everything is running fine. I have created multiple production VM. I have an another host with same hardware configuration and want to convert 2 node to 3 node cluster. I want to know the best procedure to achieve this.

HiAs you know Windows server 2003 is not officialy supported with AHV or MOVE but using the following link I was able to migrate a VM with Windows Server 2003 from an old vCenter to a new AHV cluster. https://www.vmwaremine.com/2019/01/24/migrate-windows-2003-x86-to-nutanix-ahv/#sthash.8hpeCflP.T3i44mTW.dpbsThat being said, after migrating it thw VM works fine but I have a question regarding VMware tools and Nutanix Guest tools. 1. Is it mandatory to remove the VMware tools from the migrated VM or is it just a “aesthetic” matter?2. Is it mandaroty to install Nutanix Guest Tools? I mention this cause I wasnt able do to this error when loading the NGT CDROM ISO:​​​  Thanks  

HiI have a customer with two VMware clusters, each one located in a different site (two separate buildings). I need to replace both environments with two Nutanix AHV clusters configured with Metro Availability (active-active).As part of the project, I must migrate the VMs from both VMware vCenters to the new AHV clusters using Nutanix MOVE. The AHV clusters have been sized so that either cluster can host the full workload, so the migration order is not a problem.However, physical rack space is an issue: Site A has enough rack space to install the new Nutanix nodes. Site B does not have space until the old VMware hosts are removed. Because of that, I’m considering different ways to sequence the work, and I’m not sure which approach is better.From what I understand, I should be able to enable Metro Availability either before or after migrating the VMs, and AHV Metro Availability can be enabled even when VMs are already running on both clusters. If that assumption is correct, these are

Hello evb,in a 3-host Nutanix Cluster (AOS 6.10,1 and AHV v.20230302.103003) I have one of the 3 hosts with the [/var] filled up at 92% (2.5GB on 2.9GB)The cluster is up’n’running and was OK until this warning raised by the ncc checks (v 5.1.0)Most of the space is used by:6565632 /var/log4502260 /var/log/sa2546588 /var/lib2406748 /var/lib/puppet2406072 /var/lib/puppet/reports2241772 /var/lib/puppet/reports/HOSTNAMEIn the last dir I have more than 90K [.YAML] files (of about 20KB each and created every 2 or 3 minutes, starting from the first host setup), while in the other 2 hosts I have only 14 [.yaml] files.File names are in the form yyyymmddhhmm.yamlWhat are they used for?Is it safe to delete the oldest ones?TIAPaolo 

I have a 3 node cluster running 7.3.1 and while updating LCM complained that it cannot update NICs but I need to do manually listing KB-10634. I downloaded the x722 0x800042eb update file, executed and failed at the last minute and after the update both NICs are disappeared. I spoke with Supermicro and they are not willing to do anything because the motherboard serial is more than 5 years old and OOW. But one of the Tech advised me to program this chip (AT45DB041E-SSHN) with the 722M4B.bin file at my own risk and discretion, which I did, but nothing changed. nvmupdate64e just cannot see/find these two NICs.So what I tried next was to copy the above chip content from the second good known server and programmed the corrupted chip, but still nothing changed. The good new is that I can still install and use the latest AOS with a PCIE add on X550 card and the server works fine.But, I still would like to get those 2 x722 onboard NICs back and I really appreciate your help regarding this and

Hi,I have a customer with a standalone ESXi host running a few VMs. All backups are currently performed using Acronis Backup.I need to replace this ESXi host with a new Nutanix AHV standalone cluster, and I'm concerned about Acronis compatibility with AHV.As far as I know, Acronis requires an agent to be installed inside each VM that needs to be backed up. If I migrate these VMs from ESXi to AHV, will this affect Acronis Backup in any way? Is there any incompatibility between Acronis and Nutanix AHV?When checking the Nutanix Compatibility Matrix and the Acronis documentation, I see that the Nutanix “Data Protector” option is only supported on AHV versions 6.8.1 and earlier.However, I’m not sure whether “Data Protector” is required at all for Acronis to back up VMs running on AHV, considering that Acronis uses in-guest agents.Here is the Acronis documentation for reference: Supported virtualization platformsCan someone clarify this?Thanks.

HiI've deployed a Nutanix Cluster AHV in a dark site. Im having the issue exactly described here:https://next.nutanix.com/installation-configuration-23/prism-central-stuck-at-76-vm-is-not-reachable-42437?tid=42437&fid=23 But the topic was closed without any solution so I have to search for it… In summary:After deploying the cluster I tried to deploy the Prism Central with no luck, it got stucked at 76%... AOS 7.3.1 + PC 7.3.1 The PC VM intially startas and answer by ping, however it is automaticaly restarted during the config process and it loses the net config so it gets unaccesible by lan When checking the Prism Element tasks, I see the Application Deployment task stuck atl 76 %. If I open the PC VM console to check its status I can see that it stuck on the OS boot and I can see several services such as auditd, ntpd, rsyslog, rc.localhowever it doesnt show the login prompt. If I manualy boot the VM it boots normaly (it shows the login prompt), but there is no lan configur

NC2 on Azure Deployment Pre-requisites-Hello Everyone,I started Nutanix Learning 2 months back and there are few questions which I am unable to find answers for, it would be great to hear from you guys, below are the questions I have-What kind of subscription one should have to create NC2 on AzureWhat kind of access (Owner/contributor) we should have Any reserved Network segment/IPs to deploy NC2 on Azure Minimum and maximum nodes we can create within a cluster or a single NC2 on Azure private cloud. Pre-requisites to deploy Nutanix MOVE

Hello everyone, I have a problem with my new created 4-nodes AHV cluster. in my prism element I can no longer see the two nodes ( disconnected), and the default vswitch (vs0) are gone too and can’t recreat it.

I would like to attempt PCIe passthrough of a QLogic 2662 Fiber HBA to my Windows Server 2025 Nutanix Virtual Machine so that the device shows up in device manager, but I am unable to find clear documentation on PCIe passthrough.

HiWhen I start a VM on my Nutanix server I never get display output. Why is that the case or what am I doing wrong?

I am trying to create windows 11 on AOS 6.5.1 with AHV 20230302.101026 but failing with this error.  

In the link below I read:"AHV lets you configure vCPUs (equivalent to CPU sockets) and cores per vCPU (equivalent to CPU cores) for each VM. We recommend first increasing the number of vCPUs when a VM needs more than one CPU, rather than increasing the cores per vCPU. For example, if a guest VM requires four CPUs, use four vCPUs with one core per vCPU."From my own experience, performance tests, and NUMA recommendations, I know that you should usually increase cores per CPU first. When you reach the physical cores per socket, then add a second socket.Can someone familiar with the deep architecture of AHV explain why we see that recommendation? I do not believe that an 8-vCPU VM configured as 2 sockets with 4 cores each will perform better than 1 socket with 8 cores.https://portal.nutanix.com/page/documents/solutions/details?targetId=BP-2029-AHV:nutanix-ahv-cpu-configuration.html

Hi,Thoughts from the community please on this one.We have two clusters, in two different data centers with NearSync to replicate VMs.  So my problem is when I do a unplanned fail-over I get a VM with a new GUID, all good, until my backup software (Veeam) sees this as a new VM and creates a fresh full backup.  How do I deal with this in a better way? A full backup of all my VMs is going to need a lot of space and time! 

2025-10-12 11:04:01,879Z imaging_step_cluster_init.py:1228 WARNING The Foundation IP is not in the CVM's subnet. Since the CVM by default does not allow RPCs from outside of its subnet, foundation will create ssh tunnel for cluster creation2025-10-12 11:04:01,884Z imaging_step_cluster_init.py:1143 INFO Checking whether the CVMs are ready for cluster creation2025-10-12 11:04:01,886Z imaging_step_cluster_init.py:1146 INFO [0/600s] attempt2025-10-12 11:04:01,910Z imaging_step_cluster_init.py:1166 INFO Still waiting for CVMs 192.168.80.21, 192.168.80.22, 192.168.80.23 to report ready2025-10-12 11:04:31,915Z imaging_step_cluster_init.py:1146 INFO [30/600s] attempt...2025-10-12 11:13:02,294Z imaging_step_cluster_init.py:1166 INFO Still waiting for CVMs 192.168.80.21, 192.168.80.22, 192.168.80.23 to report ready2025-10-12 11:13:32,296Z imaging_step_cluster_init.py:1146 INFO [570/600s] attempt2025-10-12 11:13:32,307Z imaging_step_cluster_init.py:1166 INFO Still waiting for CVMs 192.168.80.21,

I has install new Nutanix CE cluster, but in proceeds of installation i has lost connection.Whan cluster was installed i has check it and see these situation:One of node is not resolved, and show only IP.I has check CVMs VM in Prism Element and see this:Only 2 CVMs of 3.What i run cluster status from CVM 192.168.1.112, i see that all services is UP When i check network configuration i see this situation:And in switch configuration:All DNS records is fine.How can i register and add CVM into current cluster or what i can do to fix it?Please help with this situation.

Good afternoon.After running the NCC check, I received an error message:However, there are no errors on the disks themselves that formed the MD2 partition.There are also no hardware issues, I checked both in Nutanix and in the XCC.Is it possible to fix this problem using standard Linux tools?Here's a plan, might it work:Unmount the Partition: >umount /homeRun Filesystem Check (fsck): >fsck.ext4 -v -f /dev/md2Reboot and Remount: >mount /home

Since now 5 years i’m seeing requests for a drag n drop and/or copy paste function to be enable, all software around the are able to do it , could you please provide any valuable reason to not add this functionality to the console? I hope that you will not lose customers for a copy/paste function in the future.

Hi all, I am sometimes really wondering what programmers think when they implement features which work fundamentally different than on other similar software and are seemingly half baked. This time around templates. I would really like to know the number of templates rendered unusable because someone accidentally deleted the protection point used as base for the template, because of lack of better knowledge (ah we already deleted this VM and gone) or any visible guard rails.The expectation would be templates = (multiple) immutable images + settings. Regards

Hi all, Is creating a new image from for ex. a VMDK uploaded to an ADFS container via allow/whitelist still a thing as described in KB-2622? Uploading the image works without issues, but creating an AHV image via the AHV Image Service from the disk already located on the very same Prism Element cluster apparently not.All reference I found online was that source_url=nfs://127.0.0.1/<container>/foo.vmdk isn’t supposed to work anymore for security reasons (see KB-14160). In the KB it says to use a CVM IP instead. I however get the very same message on any of the CVM IPs as well:foo-disk-import: InvalidArgument: Address <Any CVM IP> is not supported as Remote HostAdding CVMs or AHVs IPs to the allowlist doesn’t make any difference - it just won’t work.Using acli image.create or Prism Element UI also doesn’t make a difference. Regards 

Hello guys,I found this topic https://next.nutanix.com/ahv-virtualization-27/ssh-public-key-is-removed-from-esxi-18675 from ​@mstauder  and have exactly the same issue.Since... like ever… 2022..I opened a FEAT-13832  request, but I don’t know how to check it.Nutanix need only to add a second and unmanaged authorized_keys file…Or add ssh-key define in the prism element to the ESXi … Don’t you all need this guys?  

HiI now plan to have NCX so need to which course help me to facilitate the large part of the exam

Hi Colleagues,I am trying to collect operating system information for all virtual machines through the Nutanix Prism Central v3 API.I’m using the following API endpoints: POST /api/nutanix/v3/vms/list to retrieve VM UUIDs GET /api/nutanix/v3/vms/{uuid} to check detailed metadata per VM However, in all cases, the OS information fields (e.g. guest_tools.guest_os_version, guest_info.operating_system, runtime_os, etc.) are returning null or “Unknown”, even for VMs that have Nutanix Guest Tools (NGT) installed and are visible in the Prism UI with proper OS details.Steps I’ve taken: Verified that NGT is installed and running on the VMs. Queried both /vms/list and /vms/{uuid} API endpoints. Tried multiple fields including: .status.resources.guest_tools.guest_os_version .status.resources.guest_info.operating_system .status.resources.agented_info.guest_os_name .spec.resources.guest_os_id All these fields return null via API, but Prism UI shows correct OS information.

Hi NEXT Community,We're excited to announce Nutanix Cloud Clusters (NC2) on OVHcloud!A Sovereign European Cloud OptionFor many of our customers, especially those in Europe, data sovereignty is a top priority. With this new offering, you can run your workloads in OVHcloud's European-owned and operated datacenters. This provides a clear path to ensuring your data and operations can remain under European jurisdiction, helping you address compliance requirements and avoid exposure to extraterritorial laws.Key Use Cases UnlockedBy extending your Nutanix environment to OVHcloud, you can treat the cloud as a seamless extension of your on-premises datacenters. This makes several key operations much simpler:Application Migration: Lift and shift applications and workloads to the cloud without the time, cost, and complexity of re-architecting or refactoring them. Disaster Recovery (DR): Easily build out a DR site in the cloud, using a predictable, cost-effective economic model that helps you avoi

I am following this guide: https://www.jeroentielen.nl/installing-nutanix-community-edition-ce-on-vmware-esxi-vsphere/ I am getting this error message:  Operation failed: NoHostResources: No host is schedulable: 14There is no insight in the entire system to say why the host is not schedulable.I have allocated 100GB Memory, 16 cpu cores and 2.5TB of storage To CE 2.1.  All health checks are green.VM i’m trying to run is Linux based, 2GB memory 128GB storage without any networking.I’ve started and stopped the cluster. Entered and Exited Maintenance Mode. The system is a Dell R720 with E5 2667 V2 processors running ESXI 7.0U3o I am at a loss for why this system won’t run a basic linux VM. Any ideas would be appreciated.