Deployment Success

Hello everyone,I am currently facing an issue and need assistance. I am unable to locate and download VDDK 6.0.3, which is required for Nutanix Move to Upload and migrate VMs from vSphere ESXi 5.1.I have already checked the VMware (Broadcom) website, but the minimum version available for download is VDDK 6.7.If anyone has the VDDK 6.0.3 file saved or knows an alternative source for obtaining it, I would greatly appreciate it if you could share it with me.

Hi can these compatibility errors:cause this error: or is this 2 separated issues? where the system/server is not recognized?  and if so, i have tried to find a list of supported hdd of the same size, 600gbeverything is working, except that i cant upgrade ahv 

When I go to PrismCentral registration and enter configuration items => deploy, the following message is detected and it will not deploy.~~~~Prism Element is not compatible to enable Microservice Infrastructure: domain name resolution foprism-central.cluster.local failedthe domain name resolution is okay , juste DNS server respond =10;How can we tackle this problem? ~~~~ 

Hello!I’m unable to enable FNS on my test CE nutanix cluster, even after updating both Element and Central to the newest version using LCM.If anyone have any clue of what I’ve done wrong, it would be much appreciated.

Hello, just finished installing a new CE 2.1 cluster to experiment a bit, and a new Prism Central. Trying to enable Network Controller, but it says my cluster is not supported. Is this not a feature supported by CE?Or would I have to use a different Prism Central version?

Hi! I’m trying to segment, the backplane LAN on an already existing cluster, it passes the validation, but then I get this error when it gets to about 45% Anyone know what i’m doing wrong?I’m following this documentation LinkMy CVM’s use 10.10.10.11,21,31And AHV use 10.10.10.10,20,30 Trying to get the backplane to use a 10.10.11.0/24 on a different physical switch. All ports are VLAN tagged with VLAN11 just like the This is the error I get When looking in the Foundation logs, they fail to ping eachother, but I don’t know what the issue there could be, they are using the correct IP’s and the interfaces are up on both sides.

In my struggle to find some environment to practice/test Nutanix admin stuff, I’ve now come to Nutanix Foundation (NCE 2.0 worked but is old, NCE 2.1 failed on some networking issue in my environment).Is it possible to create a small single node cluster running as a VM in VMware Workstation using for example Foundation?I made a few tries but it seemed Foundation required IPMI access to the host, but VMs in VMware don’t have IPMI (to my knowledge).  It thought maybe a new VM could be recognized by Foundation (tried both the Windows version and the VM) if it had booted DiscoveryOS, but I couldn’t find the Discovery OS image anywhere…Is there a way forward for an installation like this or is it a dead end?

We are starting to migrate from ESXi to AHV, using the MOVE application. And as the title says, all the VMs are stuck on 1280x1024 resolution when they come up on AHV. I’ve tried the “Preferred Resolution” change mentioned hereDisplay resolution in Windows Server 2016 (AHV-VM) stuck to 1280x1024 | Nutanix CommunityI change the Preferred resolution from “<Unset>” to “1920x1080”, but as soon as I exit and boot into Windows, it goes back to 1280x1024 and won’t change. Some posts mention not having Guest Tools installed before the MOVE, but that made no difference for us. I’m stuck at the same resolution, regardless of whether Guest Tools was installed prior to MOVE or not. Nor does the method of access - launch console or RDP, the VM resolution is hard coded to this annoyingly small (by 21st century standards) resolution.And all my VMs are UEFI, which is pretty much the default. And obviously that can’t be changed, without deleting the whole VM.Is there any workaround or resolution

SCSI disk 100gb, 16gb mem, Server 2016 standard desktop experience, dual xeon icelakeLikely other configurations, as this has happened with multiple VMs, still collecting data, but wanted to get something started in case others have experience with this.My first thought is obviously some uefi configuration with boot order or something, but doesn’t really make sense, since it only *seems to happen* right after tool updates. *updated as it’s not like we reboot often, maybe it will happen without updating as well.

Hello, I completed the install of the new and shiny X-Ray 5.3Nice addition for the certificate, thank you to the Team in charge.A another new feature I was eager to try is Windows, So A followed the preparation guide, got a golden image and launch a test scenario Peak Performance Microbenchmark.Unfortunately it failed preparing the VMs : group_0: Preparing VMsCause: Cause:fatal: [169.254.217.84]: UNREACHABLE! => {fatal: [169.254.252.231]: UNREACHABLE! => {fatal: [169.254.146.81]: UNREACHABLE! => {fatal: [169.254.122.189]: UNREACHABLE! => {fatal: [169.254.37.135]: UNREACHABLE! => {fatal: [169.254.178.209]: UNREACHABLE! => {fatal: [169.254.54.182]: UNREACHABLE! => {fatal: [169.254.253.253]: UNREACHABLE! => {Impact: Ansible command did not finish cleanly. Final status was 'failed', Ansible return code was 4Corrective Action: NoneI have collected the logs also , but the Google Form (Get Support for Nutanix X-Ray) does not work for me.Anyone here will to help ?

Dear Team, I have Dell server T350 with 3 HDD of 2TB and 32GB of memory and 4 Core server. I want to deploy Nutanix AHV(Hypervisor) to that server and provision some VMs for LAB. I have downloaded Nutanix CE 2.1 ISO and loaded to USB, cant move ahead of installation after disk selection. Kindly advise on this!!

Hello Nutanix Community,I'm trying to install Nutanix Community Edition (CE), but I'm encountering an InstallerVM timeout issue. The installation keeps retrying, and the hypervisor setup does not complete successfully.My hardware setup:1 HDD (480GB) → Intended for data storage. 1 SSD (2.8TB) → Assigned to CVM storage. 1 USB Drive (32GB) → Used for the hypervisor installation.Issue Description:The installation starts but gets stuck with repeated messages: INFO Hypervisor installation in progress INFO InstallerVM timeout occurred, current retry 0 I have already disabled RAID and set the SATA mode to AHCI in the BIOS. The disks are correctly recognized when using lsblk and fdisk -l. I tried wiping the disks (wipefs -a and dd if=/dev/zero), but the issue persists.Troubleshooting Attempts:Checked system RAM → I have more than 32GB available. USB Boot Media → I recreated the bootable USB with a fresh Nutanix CE ISO.

Hello,After 3 node cluster deployment, I can see 4 CVMs.Two of them looks like the same VM but duplicated.How to fix it and remove one of them? I cannot update vs0 on the node where two CVMs are placed.AHV/CVM reboot did not help. And I cannot use acli on that node. nutanix@NTNX-b7617012-A-CVM:10.170.0.11:~$ ncli vm list Id : 00062cfc-0318-cd70-17eb-005056b90eac::7fa39b58-506c-40f9-b5b8-54146d84855e Uuid : b452d890-a399-49b3-b415-e975c489d577 Name : NTNX-b7617012-A-CVM VM IP Addresses : 10.170.0.11, 192.168.5.2, 192.168.5.254 Hypervisor Host Id : 00062cfc-0318-cd70-17eb-005056b90eac::5 Hypervisor Host Uuid : f20c4224-3d4f-4472-bb79-2e8aa0968bc5 Hypervisor Host Name : NTNX-b7617012-A Memory : 20 GiB (21,474,836,480 bytes) Virtual CPUs : 2 VDisk Count : 0 Protection Domain : Consistency Group : Id

I have been trying to install Nutanix phoenix. But everytime i try to install it i run into the same error instsvcdrv.service not being able to start. I have tryed to find the file on the system and start it without any luck.I downloade ce from here = Download Community Edition | Nutanix CommunityThe full line says = Failed to start systems Management Device Drivers.See ‘systemctl status instsvcdrv.service’ for more details. The only other ones i found on here with the same problem was Nutanix CE fails to install | Nutanix Community

Hi,i have to extend a Cluster with ESXi7 HV, and in the foundation Software i have to fill in the vlanid for the cvm.I guess this is the default vlan, so with AHV i knew the commands to find out the vlanid, but with ESXI i have no experience.So could someone tell the the comands to find out the vlanid ?Regards  Uwe

I have a fresh install of CE 2.1.   Single node - Intel S2600GZ (Dual E5-2650).  LSI 2380 HBA. All SSD RAID10 disks. 4x1G Intel NICs.  ~400G for CVM/Data. I create the single node cluster ...waited 2 hours and cluster services are still down.  Thoughts?cluster status output shows:nutanix@NTNX-c3fc6bae-A-CVM:172.16.0.20:~/data/logs$ cs2025-03-10 14:44:49,368Z INFO MainThread zookeeper_session.py:136 Using multithreaded Zookeeper client library: 12025-03-10 14:44:49,370Z INFO MainThread zookeeper_session.py:248 Parsed cluster id: 5826532148493501106, cluster incarnation id: 17416115932636702025-03-10 14:44:49,371Z INFO MainThread zookeeper_session.py:270 cluster is attempting to connect to Zookeeper, host port list zk1:98762025-03-10 14:44:49,388Z INFO Dummy-1 zookeeper_session.py:840 ZK session establishment complete, sessionId=0x1958025e2ec0011, negotiated timeout=20 secs2025-03-10 14:44:49,391Z INFO MainThread cluster:3302 Executing action status on SVMs 172.16.0.202025-03-10 14:44:49

Hi, trying to install a new CE cluster to do some testing, and after I use the  cluster -s cvm1_ip_addr,cvm2_ip_addr,... createcommand, it just gets stuck on the image I’ve inserted. Any ideas what I’m doing wrong? 

Hi all,we wanne expand our cluster with 2 nodes, there are connected to Network, but wenn we start in Prism the discovery, no nodes will be found.Does anyone have a list of things we need to check RegardsUwe 

Hi TeamI am trying to setup Prism Central in Nutanix CE. I have configured the required details in Prism Console for deploying prism central. My deployment is failing repeatedly and getting the error saying it’s failed in tarball extraction phase. I have tried multiple times and every time I saw the issue in UI. I went through the /home/nutanix/data/logs/genesis.out logs to get more details on the issue. I found something interesting there. When we start the Prism central deployment, it first tried to download the prism central tarball and unzip it. One it’s unzipped then it’s start to convert the qcow2 file to image. when it start to convert the qcow2 → image , the command is configured with a timeout of 1800 sec. Please have a look into the below log line. 2024-07-01 08:55:17,702Z INFO 25030000 uvm.py:1606 Running cmd ['/usr/bin/timeout', '1800', '/usr/local/nutanix/bin/qemu-img', 'convert', '-p', '-f', 'qcow2', '-O', 'raw', u'nfs://127.0.0.1/default-container-40804253832490/pc.2022.

Hello,We are working on provisioning and deploying Cisco Firepower Threat Defense Virtual (FTDv) on Nutanix AHV using an API-based approach. Previously, we used Nutanix API for ASAv deployment, and now we want to validate whether FTDv can be fully provisioned using Nutanix API alone, without requiring manual steps during deployment as discussed in following https://www.cisco.com/c/en/us/td/docs/security/firepower/quick_start/consolidated_ftdv_gsg/ftdv-gsg/m-ftdv-nutanix-gsg.html. What We Are Trying to Achieve: Upload Cisco FTDv Image – Since FTDv requires a QCOW2 image, we need to upload it to Nutanix Image Service first. Deploy FTDv VM – We must create a VM using the uploaded FTDv image and assign networking. Apply Day-0 Configuration (Cloud-Init) – FTDv requires a Day-0 file (for IP, DNS, authentication, and FMC registration). Power On & Validate – Ensure FTDv boots with the correct settings and is ready for FMC registration. What We Need to Confirm:Nutanix API v2 vs. v3 – Nutani

We are planning to renew license for below nodes Nutanix(HCI) NX-1265-G7-2 Nodes Nutanix(HCI) NX-8135-G7-3 Nodes But in the same cluster we have four G5 nodes as well, When we try to apply core license through PC, It doesn’t allow us to only license G7 nodes and we need to select all the cores from all the nodes, It seems that we need to separate the G7 nodes from the cluster just for the licenses to apply, Are we missing anything ?

Looking for best practices or examples for enabling port-forward traffic from Nutanix AOS/AHV hypervisor to the VM.  Here is my setup:Successfully provisioned Nutanix AOS/AHV hypervisor on the PowerEdge server.   Enabled OS to iDRAC passthrough using PowerEdge iDRAC settings as per the document Accessing redfish API via OS-iDRAC interface is successful as shown below:  # curl -k https://169.254.0.1/redfish/v1{"@odata.context":"/redfish/v1/$metadata#ServiceRoot.ServiceRoot" …., Next step I would like to perform similar redfish query from the VMs. How do I enable port-forward using NAT on AOS/AHV; so that PowerEdge iDRAC redfish service network is accessible from VM?  Thank you.Viswanath

Hello,After 3 node cluster deployment with CE edition.After fresh installation, I am trying to use LCM to install Software upgrades. (NCC, Foundation and FSM).Any software I try to upgrade, all finish with failed status and at the end some drives are marked as offline: How to find:the reason why all those upgrades fail? way to bring the drives back online?

A client has requested to migrate a Windows Server VM (Domain Controller) installed in a VMWare ESXi cluster to the Nutanix cluster with AHV. I have only migrated Windows and Linux VMs with Nutanix Move, in this case I do not know if it is advisable to do the migration. I have not found any information on this matter. I would appreciate if you could tell me if it is possible to migrate the Domain Controller without any problems or if it is advisable to create a new VM configured as a Domain Controller in Nutanix. If it is possible to do the task with Nutanix Move, how should I do it? Thank you.

Hi , I am trying to setup a new Nutanix cluster on Cisco servers managed by UCSM but i am getting  a fatal error , similar like below   Servers are managed by UCSM ,Foundation can ping both UCSM ip and CVM&AHV management  gateway  Exception: Server (WZ) did not shut down in a timely manner 2025-02-17 17:11:33,286Z imaging_step.py:123 DEBUG Setting state of <ImagingStepInitIPMI(<NodeConfig(10.x.x.x) @7190>) @77f0> from RUNNING to FAILED 2025-02-17 17:11:33,288Z imaging_step.py:123 DEBUG Setting state of <ImagingStepRAIDCheckPhoenix(<NodeConfig(10.x.x.x)) @7190>) @78b0> from PENDING to NR 2025-02-17 17:11:33,289Z imaging_step.py:182 WARNING Skipping <ImagingStepRAIDCheckPhoenix(<NodeConfig(10.x.x.x)) @7190>) @78b0> because dependencies not met, failed tasks: [<ImagingStepInitIPMI(<NodeConfig(10.x.x.x) @7190>) @77f0>] 2025-02-17 17:11:33,290Z imaging_step.py:123 DEBUG Setting state of <ImagingStepPreInstall(<NodeConfig(10.x.x.x @71