5 Essential Tips for Maximizing Your Experience at Nutanix .NEXT for Bloggers
Already booked :) Thanks a lot
Storage Subnet will be in the range of CVM VLAN where as Client subnet could be your server/ client vlan to access the SMB / NFS Share.Note: You cann’t access the share if you are on same VLAN of Storage.
You can get the VM list based on the power stastus from the Prism Central. Compute & Storage → VMs Under Filter Power state filer is availabe (on, Off, Suspended, paused , unknown)Bases on the selection you can get the desire results
For AHV disk will be thin only. for ESXi you can chose thick or thin
No, this is not the expected behavior. HA will not modify anything on the VM level. Please check if disk is asisgn though Nutanix Volume or though iSCSI.Please check in VM disk manager if Disk is offline .
Linux password recover method might works but I would recommend to involve Nutanix Support in this matter to avoid any data loss / downtime.
can you confirm if the VLAN / Network is correct on the prism central VM.do confirm if Gateway & Subnet mask correct
Nutanix Move can be considered for One time migration, incase if you are looking for sync replication then Smart DR can be considered. Smart DR facilitates share-level data replication and file-server-level disaster recovery. In the event of a planned or unplanned loss of service, you can restore write access to protected shares by failing-over to a recovery site file server. Protection policies indicate failover details, including the primary location, recovery location, and the replication schedule. https://portal.nutanix.com/page/documents/details?targetId=Files-Manager-v4_4:fil-fm-dr-c.html
if your laptop is not pinging from your laptop then mean you might have issue related network.is it a newly introduced VLAN?
You have mention you have configured the VLAN ID on the switch, is the nutanix connected on trunk port or access port?if it is connected on trunk port you can configure the native VLAN on nutanix connect ports.if you dont want to configure the natvie VLAN on the ports then you have to tag it from AHVand CVM. below are commands to go the tagging on AHV & CVM TAG AHV HOST ovs-vsctl set port br0 tag=vlanidTAG CVM change_cvm_vlan=vlanid for the IPMI Ports you can connect on access port on the switch
DarkSite option is available under LCM → setting . You have loged in using different user, can you please login using admin user. and try again.
Can you put more light on the problem?Is the Windows 10 booting issue or issue with login ?Do you have VM snapshot /recovery points to restore from?
You can check on NCC, keep a eye on residency status should be OK.Keep an eye on Critical alerts
Normally you should recevied email from Credly. if you don’t account on Credly you can create one.
Active Directory Communication requires 636 if used Secure LDAP , 389 if unsecure LDAP
Data protection is based on the Virtual Machine & Volume Group, one option is to move excluded data to Volume group and protect only the VM. incase VG protection required you can add it.
Hi,NIC Failure are not very common but for NIC level redendency you can use two different NIC ports
Hi,RF2 Cluster cannot go below 3 Nodes. even 2-node cluster is not supported with all Hardware models only 1175s Series support 2-node cluster configuration. 2. What will happen after the License expires? You will lose support the node which reached end of life. Acropolis services will continue to run but you cannot upgrade to latest build as upgrade precheck failed with the error old hardware exist in the cluster.
Have a look into below article discussing Compute only nodes for oracle to save on oracle license cost.https://next.nutanix.com/community-blog-154/supercharging-your-nutanix-ahv-clusters-with-compute-only-nodes-33303?tid=33303&fid=154
Have tried reseting BMC to factory default , and can you confirm if hosts are connected on shared port ?
Normally Oracle enforce to license the Full Physical cluster, best case i have seem is have separate low core database cluster. But you can still check with Oracle Licensing expert
Whats the error you are getting , just the authentication error or anything else?
During the failover process, failed over vm is unregistered from the main site cluster and VM is registered in the DR Site.Same process if repeated during the failback process. Veeam Backup jobs are based on the VM names. I don’t think its a issue you might face issue for incremental backups. did you try to run the full backup ? please share backup failure error for more details
The best way is to use Prism Central. incase if Prism Central is not available I normally use below methology Syspre the VM and shutdown later on use this VM for cloning you can clone the VM disk to image services also for future use
can you please see the hypervisor status is the host booted?
Already have an account? Login
Enter your username or e-mail address. We'll send you an e-mail with instructions to reset your password.
Sorry, we're still checking this file's contents to make sure it's safe to download. Please try again in a few minutes.
Sorry, our virus scanner detected that this file isn't safe to download.
