Dell PowerEdge R640 bare metal bootup process failed

As you can read in the requirements: https://portal.nutanix.com/page/documents/details?targetId=Nutanix-Community-Edition-Getting-Started-v2_1:top-sysreqs-ce-r.html

You need (minimum) 3 disks. 

1. First an AHV boot disk. Must be the smallest disk in the system (can be an USB drive);
2. Second for the CVM (Must be an SSD)
3. Third for the data (Can be SSD or HDD). 

About your first error, where is the installer located? Did you check the md5 hash from the downloaded file? 

About you “1 disk listed” it looks like an RAID0 drive. So remove the RAID controller or set it to HBA/IT mode. 

Thanks ​@JeroenTielen  for helping me in this. I am trying to boot using virtual ISO bootup using Dell iDRAC but not using USB drive. 

I have verified the md5 hash and it matches as mentioned in the downloads page. 

I am unable to convert controller from RAID to Non-RAID. I am looking at different ways to get it done. 

Idrac / ilo / ipmi etc is to slow. Try booting from usb. 
 

But you need three disks in the system. 

Thanks ​@JeroenTielen . I have downgraded from R640 to R430, since I have Intel NIC at R430. I will try and get back by having necessary resources.

HI ​@JeroenTielen . I have gathered resources request to deploy Nutanix CE. Currently, R430 has Intel NIC, 2 - SSD and I USB inserted. I converted controller from RAID to Non RAID i.e HBA. Previously, this process failed due to I missed to clear the virtual disks. 

Since the chassis is located in lab and far from me, hence I am doing virtual ISO bootup and I am still facing the bootup issue as mentioned below,

The difference I observed while booting current R430 with Intel and R640 during bootup process is that, I could able to see ARP messages where are in R430 bootup I do not see them. 

In R630 though they are not Intel NIC, the process when a step ahead i.e till Hypervisor selection than R430 bootup process. 

Please let me know what I am missing here. Also please let me know what steps I need to take to bring up the infra. Thanks. 

The network cards will work. It is the booting from ilo what you probably need to skipp. Make a bootable usb stick and try it again. 
 

If a network card is not recognized the error message is completely different. 

Thanks ​@JeroenTielen , Do I need to have USB 3.0 only for bootup?

HI ​@JeroenTielen , I am using USB stick to boot up the device and I have reached till Hypervisor configurations. 

Can you please let me know whether the Host IP addresses should be same as IPMI of my device Dell R430 or any of the IP in the subnet? Thanks.

No. Host, cvm and ipmi should all be unique. Host and cvm must be in the same subnet. ipmi can be on a separate subnet. (Can be on the same as well ;))

HI ​@JeroenTielen , I have provided different IP address to Host and CVM. AHV installation process is terminated with issue mentioned below,

2 USB are inserted in chassis. 1 for AHV boot and other for bootup. List should show 4 right? Does the AHV installation failed for this reason? Please let me know if I am missing anything here. Thanks.

Hi ​@JeroenTielen , Is this a bug? I was going through a few tickets and trying to figure out the issue. 

https://next.nutanix.com/discussion-forum-14/nutanix-ce-error-while-installing-special-device-dev-none-43511?tid=43511&fid=14

https://next.nutanix.com/discussion-forum-14/ce-2020-09-16-failing-to-install-on-dell-t620-39551?tid=39551&fid=14

Can you please help me in proceeding further in this case. Thanks. 

Hi ​@JeroenTielen , I have resolved the above issue, after replacing with USB disk resolved the issue. Installation went a step ahead and I am facing another issue now, Installation always stops at 2402/2430 irrespective of how many times I tried.  

I was looking into old cases, and I modified all the timeout values as mentioned in this link. 

https://www.reddit.com/r/nutanix/comments/1drxkr5/setting_up_nutanix_ce2_failing_24022430/

but still it is getting failed at 2402/2430. Please help me to resolve my issue. Thanks.

HI ​@JeroenTielen , Do you want me to replace the AHB boot disk USB with the new USB 3.0 and try again the installation? Please let me know. Awaiting for your response. 

Just to follow up on this, further steps followed to bring up this infra is followed using ticket: https://next.nutanix.com/discussion-forum-14/ahv-bootup-process-failed-with-warning-dracut-initqueue-timeout-44515

Nutanix CE is up and running good. 

Thanks,