Installation & Configuration
This forum is the best way to get up and running with the Nutanix platform
- 1,125 Topics
- 3,037 Replies
Hi all,I am trying to install Nutanix Community edition on a Hpe DL360 Gen 9 with the latest firmware.This is the configuration:256GB RAMHPE Ethernet 1Gb 4-port 331i AdapterSmart HBA H240 with:3x 1TB RAID 0 SSD for DATA DISK 1x 1TB RAID 0 SSD for CVM Boot Disk 1x USB Sandisk Ultra 3.0 for Hypervisor BootAfter selecting the discs after a few minutes I get this error:Any ideas? Thanks
Hi all, I’m wondering if someone can help me out with the first install of a nutanix CE single cluster with esxiThe installation went fine but, and followed this link to make it work. https://vmik.net/2021/01/26/nutanix-ce-install-esxi-2021/I see that only have 1 disk in the storagepool. Is there a way to add a disk into the CVM? or do I have to mount it first. can someone help me out? many thanks.
My hardware - NX-6035-G4 running 18.104.22.168 LTS and is no longer under support. It is one of 8 in the cluster. We use this as a backup target for our two other production clusters using protection domainsI was attempting to replace a satadom because I got this error satadom has worn out - PE cycles above 4500 or PE cycles above 3000 and daily PE cycles above 15.I followed the instructions on this page to get things started, but after 8 hours of trying to clone the satadom disk the process timed out - put the node in maintenance mode and detached it from the Metadata Store. I took the node out of maintenance mode to add it back to the Metadata Store, but the option has not popped up in PE. Here is the output from an NCLI host list. Id : Uuid : Name : IPMI Address : Controller VM Address : Controller VM NAT Address : Controller VM NAT PORT : Hypervisor Address : Host S
Hello Ma’am and Sir,Does anybody tried installing or imaging a single node using phoenix? please i need some help/procedure for this as I can’t access the links given in this page it only shows “Not Found or Fordbidden”: Appendix: Imaging A Node (Phoenix) | Nutanix Community…...specifically in “Installing the Controller VM and Hypervisor by using Phoenix” and “Imaging Bare Metal Nodes”…..I created bootable phoenix using USB then i am now in the root@phoenix but I bet it requires some commands to push but have no idea on the commands and theres no search result in the internet regarding that
tl;dr how to perform pre-upgrade checks from the command line?Hello Guys,I have a question related to the performing manual / cli upgrade (command line). Here’s the scenario:AOS with ESXi as a hypervisor, multiple ROBO offices / Dark Site (no access to the internet), Dark Site server with LCM, very limited broadband: 16Mbit with static shaping (4Mbit) for management purposes and 12Mbit for businessIt is very difficult to upload via AOS GUI 4-5GB of upgrade and .json file. 3-4% / 10minutes and upload task informing about a ‘server issue’. I’m 99% sure that it related to the broadband shaping.Solution is simple:upload tar.gz install/upgrade bundle, ‘untar’, install ( ./install/bin/cluster -i ./install upgrade )My question is: is any magic command to start pre-upgrade tasks with is normally presented in GUI if upgrade package is available? It will be very helpfull to start pre-upgrade check in-advance the main upgrade.I tried to find the command in lab:-- uploaded the bundle in ‘normal
Hi Our setup will look very similar to the attached diagram once it’s setup (taken from here - https://portal.nutanix.com/page/documents/details?targetId=Nutanix-Security-Guide-v6_1:wc-network-segmentation-intro-wc-c.html). We won’t have the separate DVS for the VM’s though as these will be on the same DVS with everything else 😊 What I'm trying to understand is what the vmk2 kernel interface is used for and why this must be on its own port group and can’t use the same port used by the CVM. I’ve illustrated what I thought should be possible with the blue line. Within Prism where you change the setting for the Backplane network, you must select a port group for the CVM and for the host. However, when you try to select the same port group for both host and CVM it gives an error and won’t let you do it. Does anyone know why they need to be on separate port groups even though they will be on the same Backplane VLAN? I hope that made sense
Hello All, I am working with Affinity policies and I wonder if there is an Affinity “light”. What I mean by this is in Hyper-v clusters you have a “Preferred Server” this means that if the preferred server is available the vm will reside there if not it will move to stay running. Once the preferred server is back online then it will move back. Is this possible in AHV? Thanks,Scott
I have about 9 VM that have this error (all 130 other VMS are fine). The VMS are either Server 2012 R2 or server 2016. I have tried manually mounting NGT CD from the manage guest tools on the Nutanix VM page, then I launch the console and try to install NGT. I run the mounted cd and NGT fails saying that NGT is already installed. I’ve tried uninstalling NGT and reinstalling it from the mounted CD, but it’s not installing the latest version. How can I update NGT on these 9 VMs?
Dears:I followed the LCM dark site guide to configure the IIS, the screenshot is shown is below: But when I tried to let PC to use local web server, the error showed below: It looks builds folder is not exist in the release folder. I am not sure if this is the key point. Hope anyone could help me. Thanks!
Hi Team,In the latest release notes I see:Flow Security Policies are not supported for VMs that are on advanced networking stack. An alert is raised for VMs that are part of both VPC and Flow policy, and Flow policies are not enforced for VMs on VPCs.Is there a time frame that this will be resolved? Like this VPC is not ‘really usable’. What is the work around to have some sort of micro segmentation inside VPC? Different vlan inside VPC with an 3th party firewall? Thanks and regards,Peter
Dear Team,I had setup Dark Site web server (IIS) and uploaded unpacked LCM Dark Site Bundle and the firmware bundle (HPE). After performing LCM inventory LCM has been updated to the required version and “firmware” section is showing available new FW pack (SPP). Is any option to upload to the Dark Site server ESXi update file with metadata file or only one way to update it is to upload hypervisor metadata and binary file directly to to the Prism Elements?Software section is empty: Same question about AOS and File Server… Regards,Dominik
Our current Nutanix infrastructure has been a bit neglected for a while, AOS, PC, NCC, etc have been kept up to date but not firmware\bios or hypervisor so I need to get these done.Current infrastructure is nothing massive, two clusters one 4 node one 3 running on NX-8035-G6 and NX-8035-G7, both are AOS 5.20.4. We have one PC running at the latest version and its sitting on a separate Management vSphere cluster along with vCenter. Hypervisor is currently ESXi 7.0 Update 2a 17867351 on all hosts, this is Standard Edition so NO DRS ☹ My plan is to upgrade the firmware and BIOS etc via the LCM on the smaller of the two clusters. I have freed up one host so there aren’t any VM’s on it apart from the CVM. I take it I can just run the LCM to do the firmware updates on that host and let it do its thing without having to do anything else, it’ll shut down the CVM maintenance mode the host and restart it?Once that is complete I want to upgrade ESX on that host. I have checked the compatibil
I changed the initial password, but I keep getting a host using default password warning. The same happens with ncc checks.CVM - nutnaixAHV - rootIPMI - USERIDI have changed the above three account passwords.Which account's initial password needs to be changed to resolve this symptom?Please check.Thank you.
Hello, I recently tried to run an LCM upgrade of AHV Hypervisor el7.nutanix.202011005.30417 to version el7.nutanix.20220304.242 and ran into an issue where a failure occured during the upgrade and one of my clusters is now stuck on “Detaching node xxx.xxx.xxx.xxx from metadata ring” at a little bit of a loss as to where i can move forward from here. I am unable to launch the console for the CVM and cannot ping the CVM. I apologize for the formatting on this post. This is my first time posting and I am not too sure how to best format or attach screenshots.shown below.
HI all,We had a server HPE DL360-8 G10 - IPMI enabled. with m2 SATA stick 875317-b21 + Smart Array E208i-a SR Gen10 + 4x SSD Sata HPE and I’m trying to install AOS6.5 with AHV but it failed with error code “CRITICAL svm_rescue:926 No suitable SVM boot disk found”Very appreciate if anyone could share the way to fix this issue.
Hello, I would like to install NGT on Linux Centos 7 Create one more cd-rom for mounting the VM you want to install I know that the prism selects Manage Guest Tools as follows and then proceeds with the installation, but if it stops at the following steps, where should I check? I'd appreciate it if you could give me an answer
hi community,we want to expand the cluster by adding additional node, the server model is HPE ProLiant DX360 , currently 4 nodes are running and we want to add one node of same hardware model. the hardware is factory AOS imaged. AHV is the hypervisor on current cluster.we want to know what are the physical network connectivity is required to add the node and image AHV.on new node IPMI is connected and two 10g are connected , but we are unable to discover the node from prism element. is it required to connect the node port 1g as well to the switch for imaging?
I have figured out that the version of the kernel is 4.19.100. I have also figured out that this version is not working with my NUC11 and the i225-V NIC. I would like to replace that kernel with the 5.15 kernel as the 5.15 kernel works with the i225-V NIC. Does anyone have a procedure on how to replace the kernel in the ISO? Any help would be greatly appreciated. Thanks,Steve
We tried to create a create a new user in Prism with reference to article: Managing Local User Accounts | Nutanix CommunityWe created the new user successfully, but unable to login using the new user. Getting error: Incorrect username or password error.We have even reset the password several times, also deleted the user and created another still we are getting same error.Please help us with any solution.
Login to the community
Login with your account
Enter your username or e-mail address. We'll send you an e-mail with instructions to reset your password.