Skip to main content

Installation & Configuration

This forum is the best way to get up and running with the Nutanix platform

  • 1,297 Topics
  • 3,651 Replies
1297 Topics
M
mudassirkhanVoyager
posted in Installation & Configuration
Fatal:Running (4%)

Hi guys, trying to image 3 nodes with hyper-v 2012 R2 using foundation but 1st and 3rd node fails at 4% and 2nd node completes with 100% success. I am losing my patience :( Need some help. Thanks

4
M
8 years ago
S
santunez_clExplorer
posted in Installation & Configuration
Downgrade VMware Version

Hello Guys Any question? I have cluster Nutanix with VMWare ESXi 6.0 in a LAB, but I need the version 5.5. Is possible run a downgrade of ESXi version or is necessary reinstall Phoenix and VMware Thanks for your comment Regards Sebastian

1
Jon
Nutanix Employee
8 years ago
benwaynet
benwaynetVoyager
posted in Installation & Configuration
cluster in China stuck downloading NOS upgrade

I have a cluster in China running 4.5.x Because I upgraded my prism central to 4.6.x and didn't realize the older 4.5 was not supported I have to upgrade the cluster too. the unit in Mexico was able to download and install from the GUI. The download in China seem to get stuck, so I clicked the cancel download button. now I'm trying to upload the latest 4.5 code from a machine in china through the GUI. But it just errors out. The alerts say the download is still running. Not sure how to move forward from this point. Thanks,jb

1
Jon
Nutanix Employee
8 years ago
J
JMichelExplorer
posted in Installation & Configuration
Streched Cluster with Hyper V

Hello, is it posible to create a streched Cluster with Hyper-V? Is there a site awareness, so one side of the Cluster can go down? Or a workaround? Ideas? Best Wishes Johannes

1
mmcghee
Nutanix Employee
8 years ago
P
pbuszczykVoyager
posted in Installation & Configuration
container_mount_check fail

Hello Guys, I need your help because I run into a strange issue with my Nutanix cluster (NOS 4.6). Nutanix generates a warning as below: "Data Protection > Protection Domain > Container Mount > Containers are not mounted on all nodes". We've got only one container and it's properly mounted on all ESXi 6.0 hosts. NCC (ncc health_checks data_protection_checks protection_domain_checks container_mount_check) returns: Detailed information for container_mount_check:Node [url=http://172.30.10.13/]172.30.10.13[/url]:FAIL:Container ntnx-ds not mounted in : 172.30.10.111 172.30.10.112Node [url=http://172.30.10.12/]172.30.10.12[/url]:FAIL:Container ntnx-ds not mounted in : 172.30.10.111 172.30.10.113Node [url=http://172.30.10.11/]172.30.10.11[/url]:FAIL:Container ntnx-ds not mounted in : 172.30.10.112 172.30.10.113Refer to KB 1888 for details on container_mount_check I've checked all tips from KB article 1888 but everything seems to be OK. Furthermore the cluster has been restarte

3
Jon
Nutanix Employee
8 years ago
T
Thanakorn-ISCAdventurer
posted in Installation & Configuration
Install ESXI 6.0.0 with foundation 3.0.4

Hi, I have ploblem with foundation installation(3.0.4). In hypervision image page i choose esxi iso but when process completed, the result display AHV instead of exsi. What is the problem and how to solve it ? :D[img]https://d1qy7qyune0vt1.cloudfront.net/nutanix-us/attachment/975i251A564472B677FC.jpg[/img]

2
T
8 years ago
T
TeruVoyager
asked in Installation & Configuration
What's the behavior when the Nutanix node local storage is not enough for data of local VM?

Hi All, According to my material on hand that Nutanix will keep a copy in local storage for local data required. So if there are some storage intensive VMs running in one node and the local storage in that node is not enough for data of all local VM, some data should still need to be retrieved in remote node? would like to know the exact behavior. And one more question for DR. If I use vsphere, I still need to buy SRM license or SRM is optional (e.g. for some dedicated features?). For Hyper-V, since the DR feature of Hyper-V is not as rich as VM, can we still use the "Protect Domain" feature in Nutanix for DR in Hyper-V? Thanks a lot in advance! Best Regards, Teru Lei

3
T
8 years ago
aluciani
alucianiChevalier
posted in Installation & Configuration
Let the Nutanix Sizer do the Heavy Lifting

Nice write up from  on the Nutanix sizer Check out his blog post [url=http://www.vjenner.com/2015/10/nutanix-sizer/]here[/url] Lots of great screenshots and good explanation. In case you didn't know, The sizer lets you create scenarios that can be tailored to your requirement.

1
M
8 years ago
B
bpr-adminAdventurer
posted in Installation & Configuration
Lost a CVM while updating ESXi

I went about updating a couple ESXi hosts the old school way with using zip files and doing vib installs. My first host worked without a hitch. My second victim... I mean host is having problems. In total I installed 4 zips per host. After bringing the second one back out of maintenence mode, and having the CVM start, a few minutes later I keep getting errors about the CVM not connecting. Then I check the console on the CVM in question, and it keeps rebooting, after a kernel panic. Here's the beginning of the output: [img]https://d1qy7qyune0vt1.cloudfront.net/nutanix-us/attachment/971iE6A6E0FF19ABCDA1.png[/img] Any insight on what I can do?

3
Jon
Nutanix Employee
8 years ago
A
alunkalTrailblazer
asked in Installation & Configuration
how to find the hardware dimension,power rating of NX-3260-G4,NX-3460-G4,NX-8135-G4,NX-8235-G4.

how to find the hardware dimension,power rating of NX-3260-G4,NX-3460-G4,NX-8135-G4,NX-8235-G4.

6
A
8 years ago
A
alunkalTrailblazer
posted in Installation & Configuration
jetstress

any procedure to remove working disk from nutanix box and adding it back for doing jetstress testing can anyone help

9
joshodgers
Nutanix Employee
8 years ago
P
PVniverseAdventurer
posted in Installation & Configuration
Set-NTNXcluster showed unexpected behaviour

Hi Folks, Got something wiered happened today, might be a bug or something. I was to change current time zone setting by Get-NTNXCluster | Set-NTNXCluster -Timezone "Australia/Sydney" However it throw me an error: "The cluster name may contain only English letters, decimal digits (0-9), dots, hyphens and underscores. Set-NTNXCluster : The remote server returned an error: (500) Internal Server Error." Then I thought it might be because I did not include cluster id, so I ran below command : Get-NTNXContainer -Id xxxxxxx-xxxxxxx-xxxxxx-xxxxxx-xxxxxxxxxxxxxx::4769 | Set-NTNXCluster -Timezone "Australia/Sydney" Apprently you will find instead of using Get-NTNXCluster, I used Get-NTNXContainer which I copied from command I previously ran without double check, you would assume that will throw me an error, but it did not, it finished with a "Success". Yes, it did change the timezone on the cluster, however at the same time it changed cluster name to the Container name as wel

5
P
8 years ago
M
mikeperrinVoyager
posted in Installation & Configuration
Network Considerations

Hi Folks, I'm in the middle of a deployment and have a question. We have a pair of Nexus 3548's acting as 10 G edge switch to our Nuntanix Clusters who are trunked up to a pair of Cisco 4500's We have 4 nodes in the cluster with a total of 10 nics all 10 gig and assigned to the VDS in Vsphere. On the VDS we set the MTU to 9000 Is there a way to separate the CVM traffic from the management traffic? I would like to keep the CVM traffic from going up to the 4500's however we needed to create an SVI on the 4500's so we could manage them. I'm getting Jumbo frame errors on both the Nexus and the 4500's and when I set the MTU on the VDS back to 1500 the errors went away. My guess is the CVM traffic is what's causing the issues and I would prefre not to mess with the MTU settings on the 4500's. What is best practice here? What are other doing? Thanks

3
bbbburns
Nutanix Employee
8 years ago
D
DevarieuxaVoyager
asked in Installation & Configuration
Nutanix Template for Zabbix

Hi all! I'm currently working on a Nutanix Template for Zabbix that I will share with community once it's finished. I've a little problem with some SNMP answers Zabbix receives from prism. I'm asking for OID 1.3.6.1.4.1.41263.11.1.3.1 This OID is the cstControllerVMStatus.1. It should return Up or Down if the CVM with index 1 is Up or Down. When I run it in Zabbix, the answer is "55 70 00". Is "55 70 00" a value that means 'Up'? In this case what is the value for 'Down'? Regards,

4
D
8 years ago
H
hienleOutrider
posted in Installation & Configuration
How Foundation works?

Hello Nutanix community, Yesterday, I tried installing a Nutanix block by Foundation PC to change the hypervisor from HyperV to AHV. But unluckily error occurred with 3 nodes per 4 nodes and one node had been successfully installed. Although all 4 nodes had already run with the same configuration before, why this case happened?! After 1 day troubleshooting, I had finally and luckily installed 3 nodes left by resetting IPMI on these nodes. As I already followed the Foundation document from Nutanix, "please have a look at the logs files at /data/logs/foundation... on each nodes" to get the details of problem, but actually, in my case those log files did not contain any data that related to the errors occurred?! So how could I dive deeper into the problem that I had? They were still there but no words, to sentences, no data?! I really need a document that explains in detail how Foundation works, so that I can troubleshoot it easier than I had yesterday. Can Nutanix publicily post it

3
Jon
Nutanix Employee
8 years ago
G
giteshs
posted in Installation & Configuration
Nutanix CVM showing Pxe boot Error

Hello All, We have Four Node XC730xd-24 Cluster running on NOS 4.0.2, last nIght I have applied Esxi patches on all four esxi hosts. After all the operation one of the CVM is showing PXE boot error. As i ran the Cluster status command its showing CVM with 10.201.x.X is down. I have tried restarting the machine but no luck its still the same. Kindly help !!!

1
J
Nutanix Employee
8 years ago
K
KYFongAdventurer
posted in Installation & Configuration
Host RAM provision

Hi Team , I would like to know if my Nutanix 3 x nodes cluster has 64GB RAM each , can i provision a single VM with 128GB RAM in a single host or do i need to manual remove physical RAM and put all in a single host to provision the VM? NOS : 4.5.0.2 Hypervisor: Hyper-V

1
J
Nutanix Employee
8 years ago
F
fcardarelliPathfinder
asked in Installation & Configuration
Foundation 3 - ESXi + AHV

Hi, i have been using Foundation 3.0 to reimage 6 new nodes, they are separate in 4 blocks. There are three 6035-G4 and three 6035-C. While using Foundation i have selected to install ESXi 6.0 and the NOS version is 4.5.2 For a weird reason (im new at nutanix) three of them (6035-C) where intalled with AHV and three of them with ESXi 6.0 (6035-G4). Is this an expected behaviour? Regards. Francisco.-

1
M
Nutanix Employee
8 years ago
C
Cipo80Adventurer
asked in Installation & Configuration
New installation vsphere 6.0U1a CBT issue

Hi all, finally, after a long POC i'm a new Nutanix customer :D I'm waiting N°2 NX-1365S with 6 nodes and the idea is to create a new vsphere cluster version 6 and migrate the existing VM's from the old vsphere 5.5u2. I've just check the Nutanix support page and i see the latest supported version is 6.0u1a build 3.073.146. This version seems to be affected to CBT issue, is it possible to install the correction patch ([url=http://kb.vmware.com/selfservice/microsites/search.do?language=en_US&cmd=displayKC&externalId=2136854)]http://kb.vmware.com/selfservice/microsites/search.do?language=en_US&cmd=displayKC&externalId=2136854)[/url] after the the installation? Or install directly the 6.0u1b? Thanks in advance, and have a good w.end!

3
cbrown
Nutanix Employee
8 years ago
S
samer_mustafaVoyager
posted in Installation & Configuration
New Installation with Windows 2012 R2

Dears, i am wondering where i can find a best practice guide for deploying Nutanix Servers with Windows 2012 R2. and how to mount the boxes starting from Networking, for VDI Solution.

5
Jon
Nutanix Employee
8 years ago
K
KYFongAdventurer
posted in Installation & Configuration
Nutanix cluster hostips does not sync.

In my Hyper-v Nutanix cluster , i run the command hostips on cvm. But the hypervisor host ip it showing incorrectly. How do i sync the host ip with my cluster?

1
Jon
Nutanix Employee
8 years ago
K
KYFongAdventurer
asked in Installation & Configuration
Foundation 3.+ required tarball NOS?

Imaging with foundation failed with error shown required NOS tarball. But all NOS phoenix downloaded from portal is on .ISO format. Kindly advice please.

3
Jon
Nutanix Employee
8 years ago
F
fredodoukScout
posted in Installation & Configuration
Can configure the SSD capacity as an extended memory area in case physical memory is constraint?

Hi All We have a customer whose workload is currently fully virtualized on VMware integrated over a Legacy Three Tier Architecture. Most of their hardware devices is EoL, and after an audit of the infrastructure, we have recommended them to go in the direction of Hyper Converged Infrastructure, focussing on Nutanix They are potentially looking at a configuration of 1TB minimum per node of memory. Is there a work around to configure my SSD as an extended memory area to able to match their requirement? Kind Regards

2
Jon
Nutanix Employee
8 years ago
A
alunkalTrailblazer
posted in Installation & Configuration
foundation 3.0 issue with hyperv

HI Guyzz, recently i used foundation 3.0 to image nutanix nodes with hyperv.but imaging got stuck at 82%.then i imaged node using 2.version of foundation.Then i came to see the 3.0.1 release note in which it is mentioned the problem with hyperv imaging is removed in 3.0.1 version so if you have any base version upgrade to latest version and check the release note before using foundation hope this will help cheers

3
K
8 years ago
L
lathef1Voyager
posted in Installation & Configuration
Make default on all Hyper V hosts

i got error message when created container? Failed to modify service settings. The default virtual machine configuration store cannot be changed to '\CLHV.abcd.comiso -VhdPath CLHV.abcd.comiso': The user name or password is incorrect. (0x8007052E) Ensure the path is valid and the directory exists. If the directory is remote, ensure that it is properly configured for sharing, and that the current user and computer accounts have read/write access. what happen? can you tell me? thanks

3
Jon
Nutanix Employee
8 years ago

Badges

Show all badges
Terms & Conditions