This forum is the best way to get up and running with the Nutanix platform
Most replies
stderr: /opt/dell/srvadmin/sbin/racadm: line 13: printf: 0xError: invalid hex numberERROR: Unable to connect to RAC at specified IP address. return code: 1 ..... Traceback (most recent call last):File "/home/hudsonb/workspace/workspace/foundation_installer-3.3/builds/build-installer-3.3-release/foundation-python-tree/bdist.linux-x86_64/egg/foundation/imaging_step.py", line 124, in _runFile "/home/hudsonb/workspace/workspace/foundation_installer-3.3/builds/build-installer-3.3-release/foundation-python-tree/bdist.linux-x86_64/egg/foundation/imaging_step_type_detection.py", line 294, in runStandardError: Foundation failed to detect node type at 192.168.110.4.
Hi There,So I made a stupid mistake and removed 2 x eth interfaces from all 3 nodes within the only virtual switch on my cluster. This was within Prism Element. I can still access AHV via IPMI, can no longer access Prism Element. Is there a way to add the eth interfaces back onto the virtual switch via AHV/AOS through the cmdlets?Cheers in advance.Adam
I was able to successfully overcome the lack of the proper igc modules for my Intel 2.5 gbps nics on my protectli homeserver (like a NUC but not). The blog here helped, and I simply downloaded the igc module from Satoshi’s site. But now the problem is I restart the installer with “./ce_installer && screen -r”, but it fails with the following error that makes it sound like it is upgrading versus installing for the first time. Following is picture of the error: Is there way to signal this is as a first time installation? Should I wipe all the disks in my system before doing the install? (The disks are currently part of a Ubuntu KVM install that I assumed could be be blown away by the Nutanix installation.)Thanks in advance for any tips.
I am using Nutanix on VSphere 6.5, and am affected by the 100% Memory usage alerts as described in KB article 000004465. I would like to create a folder in VSphere called Nutanix CVMs, which will not have the memory alerts enabled, and would like to move the CVM VMs in to this folder. Can anyone advise whether it’s safe to move a CVM VM in to another folder after is has been deployed? Part of me thinks this is a safe / normal procedure, as I’ve done it countless times with normal VMs. However, due to the complex nature of hyper-converged infrastructure and CVMs I understand I need to be very careful. Thanks for your help Jason
I have installed Nutanix Community Edition but cannot complete the Next authentication.I have configured the IP of the CVM and the external IP of the cluster.The CVM can resolve the name of www.nutanix.com.I can log in to my.nutanix.com, portal.nutanix.com, and next.nutanix.com. However, when I enter my email address and click "Get Started" at the following URL, I receive the message below and cannot proceed: "It seems your My Nutanix account is not activated, please go to my.nutanix.com to complete the process"https://www.nutanix.com/products/community-edition/registerI have already created an account and can log in freely. Is there anything additional I need to do?
Successfully connected with my GCP account, added drive, configured as persistent, but still can’t launch - the status is UNAVAILABLE for both Sandbox and Utility server.
# On March 4, I posted the following but I have written the wrong answer myself, and the status of that bank has become "solved". # Actually it remains unresolved. I will post it again because I want to resolve it by all means. # The problem is "CVM can only communicate with AHV". Dear All, I am trying to build Nutanix CE into the environment of Nested ESXi. I downloaded and prepared the latest version of ce - 2018.05.01 - stable.img.gz. The ESXi to build the AHV is 6.0. First of all, we started to work as a single node cluster, we plan to develop into a 3 node cluster if it works. 192.168.0.27/24 to AHV, GW: 192.168.0.254. I set up CVM 192.168.0.28/24, GW: 192.168.0.254 and started the installation. After waiting for a while, a message stating that the installation was successful is displayed and the message "Nutanix CVM IP: 192.168.0.28" is displayed. However, only AHV can communicate with this CVM, and it can not communicate with other devices on the same subnet. If you che
Hi, trying to install a new CE cluster to do some testing, and after I use the cluster -s cvm1_ip_addr,cvm2_ip_addr,... createcommand, it just gets stuck on the image I’ve inserted. Any ideas what I’m doing wrong?
After I tested different features about Prism Central I’d like to reduce the size of the VM. Now the VM has 18vCPU and 70Gb RAM, it’s to much for my normal use. Is it possible to reduce the vm?
Hi guys. We are in the process of acquiring Nutanix products, but we need to know something crucial. We currently have more than 100 ESXi hosts, separated in 2 sites. We have a metro cluster, all the datastores are sync, this is full active active, with EMC VMAX All Flash and VPLEX. As of today (May 2020), can we do such thing with AHV and ADSF? It is supported? I’ve seen the Sync DR here: https://cloudvm.es/nutanix-ahv-synchronous-replication, where i can see you can do it VM by VM. But what about if i want to protect at datastore/container level? All of the VMs. We have more than 3000 VMs. We need to know if we can accomplish the same with Nutanix. Stretched storage and VMs on both sides, for obvious reasons (balance, availability). If one of the sites crashed, HA all the VMs automatically to the other. Is there a video or pdf showing how it works? Thank you!!
I’m attempting a new installation of CE. The installation itself completes with no apparent errors but I can’t connect to either the AHV or CVM IP’s assigned during the install. The onboard server NIC is a four port HPE 331i which has a Broadcom chipset. Three of the ports are connected to the same network vlan that the IP addresses are tied to. I have tried trunking them on the switch side, leaving them all on as individual ports and enabling/disabling each so that only one connects at a time and have had no luck with any of these strategies. I’ve tried to log into the console of the CE server but haven’t been able to find credentials that work. Any ideas would be much appreciated since I’m so close to be done hopefully.
How do i disable the features in Prism Central so i dont get a License Violation? I dont have a license for Prism Central - so just want it with the starter license..
We have to do a deployment of 5 HPE DX nodes with AHV as hypervisor. Is it mandatory to have the iLO ip address in the same subnet as CVM & Host ? If not then do we have to give 2 IP addresses to foundation VM ? Let me know if anything else is needed.
facing this error while configuring new cluster.foundation.config_manager.EventTimeoutException: Timeout (1200s) in waiting for events ['VMD BIOS settings completed', 'Skipping BIOS settings updates for VMD', 'fatal', 'fatal', 'fatal'] imaging_step.py:164 ERROR Exception in running <ImagingStepPhoenix(<NodeConfig() @b2b0>) @a340>Traceback (most recent call last): File "foundation\imaging_step.py", line 160, in _run File "foundation\decorators.py", line 78, in wrap_method File "foundation\imaging_step_phoenix.py", line 481, in run File "foundation\imaging_step.py", line 346, in wait_for_event File "foundation\config_manager.py", line 351, in wait_for_eventfoundation.config_manager.EventTimeoutException: Timeout (1200s) in waiting for events ['VMD BIOS settings completed', 'Skipping BIOS settings updates for VMD', 'fatal', 'fatal', 'fatal'],848Z imaging_step.py:123 DEBUG Setting state of <ImagingStepPhoenix(<NodeConfig() @b2b0>) @a340> from RUNNING to FAILEDi
Hello, Where from i can download prism central ova (for vmware)? I used several links, but always i am redirected to support portal. But i have community account only... Regards Mindaugas
We are using a Prism Central Installation with several Clusters in different Sites. For the Administrators on Site, we want to configure a user on the site based prism elements instance, which is a viewing User, with the following additional permissions on the local cluster / Prism Elements: Viewing, Power on and off for all virtual Machines and also a one click shutdown of the whole cluster in case of power outages. We don't want to use the Prism Central User Configuration for following reasons: Prism Central is not accessible in case of line outages or power failures in our sites. And for security reasons and limited skills of the staff on site, I really appreciate not to give admin permission to the site staff. Any Idea, how to deal with this situation ? Thanks Oliver
After replacing the motherboard and raid controller, cvm does not start. Error "Device 0000:59:0.0 not found..."
Hi all, the import SSL certificate form allows me to choose between key’s format. I have RSA2048, ECDSA384 along with other ECDSAs. I am pretty sure I sumbitted a ECDSA384 key with secp384r1 curve. I can safely paste my key here because it’s now revoked: -----BEGIN EC PRIVATE KEY----- MIGkAgEBBDAzjnBwsncbnlR643ngw7M8/urUzuSVNNGjB84kTxgCyplXsbSuKzyl gxiijfhY3vOgBwYFK4EEACKhZANiAAS5DDtPOWrgYA/XKxzNEM1E3TER7Ol70njH JsQC+WU8lMH4d0s9G9MfIzQ1qHB7PukydkpdwMV2MYpaKpmQyrNO75zeRr/Jle/M 76vLL7FbZP9lzvwVTnJVXttXhBctM0o= -----END EC PRIVATE KEY----- Please can anyone explain me what’s wrong? Thank you so much! francescm
hi Friends, We have a 3-node Lenovo SR530 with IPMI IPs set. We are trying to install and Setup the Cluster remotely (vpn). Below are the details of IPs,XCC IPs - 172.31.199.x (all 3 nodes of same subnet)AHV IPs - 172.31.199.x (all 3 AHVs IPs of same subnet as XCC)CVM IPs - 192.168.5.x (All CVM IPs with thier default IPs) Problem:I have installed Foundation Applet 5.1 and while running on my laptop, its not able to detect the nodes. Any idea on what to check? The other way suggested in one of the forums was execute the cluster create command in one of CVMs. But all the CVMs have same IPs (192.168.5.2). Should I change the IPs of all CVMs with unique IPs matching with AHV and XCC Subnet IPs and then execute cluster create command? How can I know the CVM IP address from the AHV cliFoundation Applet error messageJava Web Start 11.311.2.11Using JRE version 1.8.0_311-b11 Java HotSpot(TM) Client VMJRE expiration date: 19/2/22 12:00 AMconsole.user.home = C:\Users\KishoreSalipalli-------------
I have old hardware that is no longer used for production and the server can only be turned back on after we repair it. Currently, I will use this hardware as a development server or backup server, but when I check the compatibility for NX Gen 3, it is no longer there. How can I find a version that is suitable for my Gen 3 server?
Hi all, Our nutanix has been running for a little bit more than 2 years now. Due to changes in our work environment (and the fact that our 3050 nodes started on NOS 3.5) we decided to use the opportunity to perform a field install, and do the upgrade to nos 4.5. We were getting the BMC error for a little while (since we were on nos 4.x). The reimage proces went perfectly but, and I was sure that during the reimage the BMC firmware should have been update, this was not the case. BMC firmware is still version 1.87. NCC is giving us warnings about that. I searched the site, but I can't find the BMC firmware files. Do I need to go get them from the supermicro site (not fond if doing things that way), or is there a nutanix link to the most recent BMC firmware? Some pointers in the right direction would be appreciated Thank you very much kind regards Marino
How many nodes we can deploy at the same time in nutanix ? Is there any limit or shall we just go ahead and deploy all the nodes at the same time ?Same query is related to cluster expansion, can we add multiple nodes at the same time in existing cluster ?Thanks
Dear All,Can we use 1 G port for Hyper VM Traffic on Nutanix?
Hello, If I have 3 Nutanix nodes and I cluster them together. How can I make a separate VPC for a test stack and a separate VPC for a Production stack? So that way I can build my VM's on the test stack and once they are good to go...I can do the same steps on my Production stack. I would like to have 2 isolated stacks for testing and production. Is this possible? Thanks
Can any one help on the api call to pull the role assignments user list through prism central?
Already have an account? Login
Enter your E-mail address. We'll send you an e-mail with instructions to reset your password.