Solved

Change CVM name


Badge +2
Hi there,

I have a simple question for cvm.Is that possible to change cvm name?

Thanks,

Sungho
icon

Best answer by Jon 8 August 2016, 19:25

Actually, yes , we have added support for this in commercial 4.6.1 and higher.

Command is:
$ change_cvm_hostname

View original

16 replies

Userlevel 7
Badge +35
Hi 

Let me see what I can do to get you some info - Thanks
Userlevel 3
Badge +16
Unfortunatly at this time there is no way to change the CVM host name - it's automatically generated from the Block SN and the location in the block.

We're working on changing this, but in the mean time you can setup the DNS entries so that it points the name to the correct IP, even if the display name once you've logged in is incorrect.
Badge +2
Thank you for the reply.
I tell to my customer that there is no way to change CVM name at this time. 🙂

Thanks!
Badge +2
Has this issue been corrected?
Userlevel 7
Badge +30
Actually, yes , we have added support for this in commercial 4.6.1 and higher.

Command is:
$ change_cvm_hostname
Badge +2
Hey Jon,

Just tried to run this change hostname command however tells me I need root permission. when logging into the cvm on my block I have been using the default nutanix/nutanix/4u, when trying to su to root it tells me the password is wrong, is there a default root passwords for the cvm's?

Thanks
Ryan
Userlevel 3
Badge +19
try "sudo command " instead of "su"


Badge +5
Hi, same problem here.
I tried sudoing the command but no joy: password not correct or command not recognized.


Badge +5
I finally solved with sudo and writing the entire path to the command
Badge
Is there a documentation link for this command as well as hostname requirements? I was under the impression they had ot more or less conform to CVM naming convention.

Thank you
Badge +3
In fact you need root rights, so

$ sudo su -
# change_cvm_hostname

...at least so I did 🙂

BR,
Rick
Userlevel 1
Badge +9
Per KB 3517 (https://portal.nutanix.com/kb/3517), make sure you follow the naming convention requirements:
The host name of the Controller VM must:
  • Start with NTNX-
  • End with -CVM

Thanks!
Badge +4
I actually changed our CVM-hostnames (still with the mentioned naming convention, but to match the naming of the physical nodes) - and it worked fine execpt for one thing:
In the cli it has the rigth name, but in the webconsole/ prism it still has the old name listed as "VM name".

How can we change this?
Badge +1
Hi there,

I'm also asking myself if there is an option to display the changed CVM name in Prism UI?

Best regards

Stephan
Badge +2
Specifically, after changing both the AHV host's hosname and the CVM's hostname, when I go into the VM page of the Prism UI, neither the CVM "VM Na

me" or it's associated "Host" name show up as changed. They both still show the original hostnames of the AHV hosts and the CVMs.

In the "Hardware" page of Prism, the AHV hosts "Host Name" are correctly set after the change and the reboot of the CVM.

ssh to either the host or CVM and local hostname shows up as correctly changed at the command prompt as well as with the "hostname" command.

Edited: After a few additional minutes, the AHV hostname associated with each CVM on the VM page did update, but the CVM "VM Name" still did not.
Badge +12
Seeing a very similar issue here.

AHV and CVM rename
Under > Hardware
AHV Host rename is showing properly on overview, properly on the table and diagram.

CVM is NOT renamed within PRISM.
To do that - follow these steps
https://portal.nutanix.com/#/page/kbs/details?targetId=kA03200000004yQCAQ
KB - 2717

Reply