Nutanix Connect Blog

Welcome to the Nutanix NEXT community. To get started please read our short welcome post. Thanks!

Showing results for 
Search instead for 
Did you mean: 

Part I: How to setup a three-node NUC Nutanix CE cluster

This blog was authores by @MarcNutanix Sr. Systems Engineer at Nutanix.

The following is my experience in successfully setting up a three-node Nutanix Community Edition (CE) cluster for my home lab.  During this process I did a lot of research and reviewed the CE forums, [go].

Since much of the information can be found in many locations, I thought it was a good idea to put them together in a single post that consolidates the details on how to get your first Nutanix CE cluster up and running.

To build a single NUC Node you need the following

► (1) Intel NUC Kit NUC6i7KYK Mini PC [go]

► (1) Transcend 32GB JetFlash 710 USB 3.1/3.0 Flash Drive [go]

► (2) Sandisk X400 Solid State Drive - Internal (SD8SN8U-512G-1122) [go]

► (1) Crucial 32GB Kit (16GBx2) DDR4 2133 MT/s (PC4-17000) SODIMM 260-Pin Memory - CT2K16G4SFD8213 [go]

A single NUC using the ingredients above will cost you around $1,000.

NOTE: Nutanix CE can run on 1, 3 or 4 Node Configurations.  I specifically selected a (3) Node configuration in my home lab since this is also the minimum config for our Nutanix Customers in the real world.

The hardware install is very easy, just flip the NUC over, loosen 4 screws at each corner, remove the bottom cover and insert memory and the SSD drives.



Now that you have your hardware setup, the next step is to register and download the Nutanix CE software.

Register to join the Community

► Start here

► Scroll down the page and click on Get Access


 ► Fill in the info and click on submit.



 Now that you have access to the Community

► Download the Nutanix CE Image file [go]

► Next, you have to get the image onto a USB Drive which your Node will boot from. I used Rufus on Windows,

► Verify you have the following files downloaded.

Picture1.pngCreate a bootable Nutanix CE image on your USB Flash Drive

► Insert your USB Flash Drive.

► Run Rufus and click on the Image Icon.



► Make sure to change below to “All files” instead of ISO file, find the Nutanix CE Image file and click Open.



 ► Just click on Start and the Nutanix CE Image will be “burned” onto the USB Flash Drive.



► IMPORTANT: Each NUC needs its own USB flash drive to boot up and run Nutanix CE.

► Now plug in the USB flash drives into each one of your NUCs, power on the NUCs and install Nutanix CE.

Planning my (3) Node NUC Nutanix CE Cluster



I wanted to take some time and explain how my home network setup is configured and how my Nutanix CE home lab will interface with it. The Nutanix CE configuration will be sitting on my bookshelf in my home office, ready for use!

So my cable modem and wireless access point (with 4 Ports) sits on the main floor.  All my laptops, tablets, phones, devices connect to the main floor WAP.

Since I wanted to have my Nutanix CE home lab sit in the bookshelf of my home office which is upstairs, I did the following:

► Purchased a gigabit ethernet switch for my lab

► Purchased a WAP to extend my home wireless

► Simply plugged in each NUC’s ethernet port into the gigabit ethernet switch

► Since the WAP is extending my home wireless, anything I plug into the bookshelf switch is connected to the internet

NOTE: You need to have internet connectivity when you log into the CVM or Cluster IP address via Prism to manage and run your Nutanix CE Cluster because this is tied to your Community email/password on

My configuration

Host (Physical NUC) IP Address:

Host Subnet Mask:

Host Gateway:


CVM (Each Host runs a Nutanix Controller Virtual Machine) IP Address:

CVM Subnet Mask:

CVM Gateway:


Things to do after Nutanix CE Installation and before you create your Cluster

After the installation, the first thing I did was to change the CVM memory which by default takes up 16GB.  The NUC has a total of 32GB of memory, I wanted to reduce the amount of memory the CVM default takes so I can run plenty of virtual machines in my Nutanix CE home lab.

I decided to reduce the CVM memory to 8GB.  After a couple weeks of using my Nutanix CE Cluster with plenty of virtual machines, I have not experienced any problems or concerns at all running each CVM with 8GB of memory.

To reduce the CVM memory to 8GB you can either (1) log directly into the Nutanix CE node or (2) SSH into the Nutanix CE node.  Either way make sure to log in as “root” and not “nutanix”.

NOTE: Remember anytime you log into the NUC or Node you use “root” and anytime you log into the CVM you use “nutanix”. The password by default is nutanix/4u for either “root” or “nutanix”.

To set the CVM memory to 8GB

► virsh list --all

► virsh shutdown <CVM-Name>

► virsh setmem <CVM-Name> 8G --config

► virsh setmaxmem <CVM-Name> 8G --config

► virsh start <CVM-Name>

► virsh list –all, to make sure CVM is back up and running

Confirm CVM memory is set to 8GB

► virsh dominfo <CVM-Name>


Creating the Cluster

Now that you have installed each NUC node and configured each CVM with 8GB of memory, now is the exciting step of setting up a Cluster with your NUC Nodes.

► SSH into one of the CVMs, I opened up terminal on my Mac and typed “ssh nutanix@” and used the password “nutanix/4u”

► Type “cluster –s cvmip,cvmip,cvmip create (no spaces between the commas)

► Example, to create my cluster I used “cluster –s,, create”


► After completion, hopefully everything is up and running

► You can type “cluster status” and each CVM will display its status



Logging into your super cool new Nutanix CE Cluster for the first time

► Open your web browser of choice and connect to one of your CVM IP Addresses

► Use “admin” for the username and the password

► You will then be asked to change the password

NOTE: You need to make sure your laptop, tablet, etc. that you are using to access Prism also has internet access since Prism will ask for your email/password that you used to log into the Community site (

Picture1.pngCongrats!  You are now logged into your Nutanix CE Cluster

Confirm that CVMs are set to 8GB of memory

- Click on Home – VM




- Click on Table, check the Include Controller VMs box and verify your CVMs are running at 8GB of Memory 


Now let the fun begin!

Here is a pic of my Nutanix CE Home Lab Bookshelf Cluster 


Disclaimer: This blog may contain links to external websites that are not part of Nutanix does not control these sites, and disclaims all responsibility for the content or accuracy of any external site. Our decision to link to an external site should not be considered an endorsement of any content on such site



Excellent writeup Valeria!  Overall the process looks simple, but it's great to have a nice, clear write-up like this!  Thanks!



Great writeup ! just one question, after tconfiguring the host and CVm ip address, therer is teh set up single node cluster question (sowmthing like that anyway, do u chck that or leave it un checked?

Nutanix Employee

Happy Friday @JasonMills, since I was setting up (3) Nodes to place into a Cluster, I left the Single Node Cluster unchecked during the setup of each of these Nodes.

Nutanix Employee Gus
Nutanix Employee

 @JasonMills: Even when I am setting up a one-node cluster I still leave that checkbox unchecked and I manually create the cluster from CLI:

cluster -s <CVM1 IP>,<CVM2 IP>,<CVM3 IP> create
Nutanix Employee Gus
Nutanix Employee

@valeriavong: Thank you for this great article!

Just one clarification: In your screenshots seems like you used the .gz (compressed image) file to burn to the USB thumb drive but if I'm not mistaken, it should be the uncompressed image file (.img). Is this correct?


Excellent write up. I have just one question about hardware configuration. Here in my country I didn't found Intel NUC for sell, and import from US is not an viable option. My question is, the Nutanix CE cluster might runing with the hardware configuration listed below?

Lenovo ThinkCentre M710 Tiny:
- Intel Core i7-7700T Processor (8MB Cache, 2.90 GHz)
- 32GB ( 16+16 ) DDR4 2400 SODIMM
- 500GB Hard Drive, 7200RPM, 2.5", SATA3
- 512GB SolidState Drive M.2 PCIe Opal
- Integrated Gigabit Ethernet Port
- Intel Dual Band Wireless-AC 3165, 802.11ac, 1x1 Wi-Fi + Bluetooth 4.0

I think I can found that hardware here in Brazil.


Nutanix Employee Gus
Nutanix Employee

@freed_m_lima : Yes. That configuration looks good. I would increase RAM to 64G if you can but even 32G will do Ok.

You don't need the WiFi adapter but I assume it is built-in.


Thanks Gus. 32 GB is the maximum memory supported. But what about the 500GB Hard Drive, 7200RPM, 2.5", SATA3? You think it will works fine?

Nutanix Employee Gus
Nutanix Employee

Ok. 32G RAM will be OK for one node. 

Yes, drives look fine. You want to have one SSD + one HDD minimum. Both your drives look good to me. Even your SSD can be a little smaller if you like (250G for example) and the HDD can be as big as you like.


Actually I´m planning to create a three node cluster and decrease the CVM memory from 16GB to 8 GB as I read at this post.


Hey one question .. is it possible to install Esxi Hypervisor or are we limited to Acropolis ? You didnt mentioned nothing about the HyperVisor.




Nutanix CE is limited to AHV for the base hypervisor.  Some have tried nesting ESX with varied results.


Does any one know if intel Optane's works well with Nutanix CE? I'd like to set up a test lab at home. i am thinking  of a 3 node NUC build.



x6 G.Skill Ripjaws 16GB (1x 16GB) DDR4 2133MHz

x3 Intel Optane 32GB M.2 Memory Module

x3 WD WD10JPLX 1TB Black 2.5" 7200RPM 9.5mm SATA3 Hard Drive


Be interested if this has been done before and anyones thoughts.






Great Write-up!

I have one question about logging into Prism in a disconnected state. I plan on traveling with my 3 node cluster and am wondering what I do when I don't have connectivity to the internet. Looks like I may need to figure out a way to tether my phone if I'm Oscar Mike.





Prism will have to be able to reach the internet.  No way around it.  How that's provided, either by cabled in hot spot or by guest wifi is fine.  



Be wary of which drives you choose.  I went with Intell SSD 600p Series nvme drives.  They quickly went into read-only state.  Its a safety feature built into the drive, apparently. I guess Nutanix was too much for them.,4738.html


 Intel clarified the nature of the read-only feature, which is not based upon the endurance limit. All SSDs have spare area that is dedicated to replacing failed cells. The Intel 600p only switches into a read-only mode when the spare area is exhausted. Intel also noted users can copy the data from a read-only SSD by installing it as a secondary drive in another computer. 


Can the CE edition be setup on AMF FX processors as well?  Is working for my i7 however for a FX8150 I receive an error "invalid arch-independentELF magic" - Cool error BTW.


I've setup a cluster with 8GB CVM memory and AHV 5.1. It worked but after two weeks the CVMs have run low on Memory despite the cluster is running no load at all (no VMs beneath the CVMs).

:~# ncli cluster get-timezone
# There is insufficient memory for the Java Runtime Environment to continue.
# Native memory allocation (mmap) failed to map 258998272 bytes for committing reserved memory.
# An error report file with more information is saved as:
# /home/nutanix/prism/cli/hs_err_pid14868.log


One of the CVMs wasn't reachable via PRISM anymore. I've noticed that there's an option to configure the CVM memory in PRISM to increase memory. However, that doesn't work showing:


"Memory update cannot run, since all nodes are low memoryInvalid parameters passed" :-).


So while it seems a little bit odd the CVMs need more than 8GB on an idle cluster, sticking to the recommendations seems to be the better decision here.



Hi all. I'm trying to install the Nutanix CE but when I'm close to the end of my installation I saw the message below:


Wating for the Nutanix Controller VM to start up.....................

"A problem was encountred. Please review the contents of /home/install/firstboot.out for details, and refer to the documentation or the Nutanix NEXT community for nets steps."


Please, somebody can help me?



WhenI´m trying to create a cluster I see this  message....


[root@NTNX-1aec6bf5-A ~]# cluster -s,, create
option -s unrecognized - ignored
Usage: cluster <options> graphfile
-C k - generate no more than k clusters (0)
0 : no limit
-c k - use clustering method k (0)
0 : use modularity
1 : use modularity quality
-o <outfile> - output file (stdout)
-v - verbose mode
-? - print usage


Any suggestions?!

Nutanix Employee Gus
Nutanix Employee

This is likely because you are logged in to the host (NUC) and not the CVM. Be sure to ssh to the CVM first and run the command from there.

You should login to the CVM as nutanix.


Perfect @Gus, Thanks!

Now, what are the IP addresses or hostaname I should use to DNS and NTP Server?

Nutanix Employee Gus
Nutanix Employee

It depends. If you have a domain in your local network or lab, you can use the domain controller as both DNS and NTP. Or you can simply use external ones such as Google's public DNS ( and Public NTP:



Perfect @Gus, thanks.


Now I reboot my cluster and I´m not able to conect. Prism doesn't work and SSH neither.


When I connect a monitor and keyboard direct on the physical node I can access the CVM, but just like root, the nutanix user doesn't work.

Any idea what may happen?




That the message what I see...




While editing my post I accidently deleted the details. So just added again.

Below is the screenshot of the issue I am having when installing the CE on my Supermicro C2750 system fitted with 32GB RAM, 1 x 1TB SATA and 1 x 250GB SSD drive. I have tried installing several times but no luck. This screen shot is from the Installer routine. The installer is not able to detect any drives. For some reason it doesn't even find my 8GB USB flash drive which the system is being booted up with.


CE Install Error.PNG



Logged on as root after the installer routine reverts to the installation screen. The FDISK does indicate the disks are attached to the system and the AHV/Centos can detect them but for some reason the requirements detection script thinks the drives are no good.


Nutanix Employee Gus
Nutanix Employee

Looking at your screenshot, it seems like you are connected to the AHV host (the NUC) and not the CVM as you stated. Login to the AHV Host as root instead of nutanix.

If login is sucesful, then you can ssh from the AHV host to the CVM either by using the CVM real IP or the CVM's internal Nutanix IP (the backdoor)


@jas5.1 has been known to require more memory. On a the commercial version, 16GB CVMs give the same issue after a while. We now use to deploy 32GB CVM all the time.


On the CE, I wonder if 12GB would make it for a while. have you tried ?


I'm thinking of doing my own 3 node NUC cluster. But 16GB overhead on a NUC is quite a lot.


@Gus Sorry for the confusion, you are right this is at the AHV stage, the installer does not find the drives so it does not proceed further. So the screenshots are after logging on as root.

Nutanix Employee Gus
Nutanix Employee

 @Akim - A three-node NUC cluster is a great project/lab and it works extremely well.

Unfortunately memory utilization will continue to be an issue as the NUCs support up to 32G. However, it still works great and you can run a few VMs on the cluster and demostrate all Nutanix features including 1 node failure.

I've always set my CVMs with 16G to avoid issues. Yes, AOS 5.1.x requires 20G CVMs but please install the latest CE (2017.07.20) and you try with 16G CVMs.


Thank you Gus. I thought so. I don't have the NUCs yet. Therefore I hesitate to buy my NUCs. It's 4k$ for something that might not last a year, given the fact our product is evolving so fast ^^

Would love to see a microblock for demos able to support 64GB RAM per node Smiley Happy I looked to create my own cluster with MicroATX board, but then it's not that much transportable anymore. An alternative I thought of was to create a cluster in the cloud. Then it's also pricy.

Well, for now, I'll do with hpocs. And perhaps the cloud solution might get cheaper in time.


@Gus  I managed to installed CE as a single node on my other Intel i7-3820 machine and made sure I could logon to Prism. The Host IP is and CVM = and my Router Gateway is I then shutdown the node and transfered the SSD/HDD to my Supermicro Atom system. It powers up perfectly and I can log on to AHV as root and do SSH to the CVM.


But the Host NIC is is not accessible by the CVM because AHV does not have access to the Intel NICs (Interl I354). The original machine on which I had installed CE has a different model of Intel NIC.


I can ping the above IPs from the AHV and CVM consoles I am led to believe in the interal networking is working but the external facing connection to the physical NIC is broken and I need to re-initialize the Host networking.  Can someone please help me out here?









About the Author
Top Kudoed Authors